Effect of Combustor Casing Deformation on the Air Flow at Annulus
Keywords:
Can combustor, annulus flow, velocity profile, pitot static tubeAbstract
This paper describes an experimental analysis of the flow inside a real part of a can combustor used in Babylon/Iraq gas turbine power station. The combustor which has been studied contains deformation in the outer air casing due to the high temperature within the liner. Flow quality through annulus is crucial as it feeds air to the primary, secondary and dilution holes. One of the most important criterions of combustion chamber design is to have uniformity of pressure in the annulus region as early as possible which ensures flow split through various liner holes and minimum combustor length .This can be achieved by sufficient as well as efficient diffusion of air from compressor. Used pitot static tube to measure the velocity profile at ten stations in the outer annuls. The performance of the system was also assessed in terms of total pressure loss and static pressure recovery between the first and last measurement stations. It was observed that the deformation effected on the flow uniformity and penetration of air through the holes, thus effected on the performance of the combustor.
References
Fishenden,C.R., and Stevens, S.J., 'performance of Annular combustor dump diffusers ',J. Aircraft, , 1977, Vol.14,No.1, pp.60-67.
Rhode, D. L., Lilley,D. G., and Mclaughlin, D. K., 'Mean flow fields in axisymmetric combustor geometries with swirl', AIAA J., 1983, Vol.21, No.4, pp.593-600.
Samimy, M. and Langenfeld, C. A., 'Experimental study of isothermal swirling flows in dump combustor', AIAA J., 1988, Vol.26, No.12, pp. 1442-1449.
McGuirk,J. J.and Palma,J. M.I. M., 'Experimental investigation of the flow inside a water model of a gas turbine combustor: part I: mean and turbulent flow field', J. Fluid Eng., 1995, Vol.117, pp.450-458.
Carrotte,J. E., Bailey, D. W., and Frodsham, C.W., 'Dailed measurements on a modern combustor dump diffuser system’, J .Eng Gas Turbines power, , 1995, Vol.117, pp 679-685.
Rahim, A., Singh, S. N., and Veeravalli, S.V., 'Liner dome shape effect on the annulus flow characteristics with and without swirl for a can-combustor ', J .Power and Energy, IMech, 2007, Vol.221, Part A.
Rizk, N. K. and Mongai, H. C., 'Three dimensional analysis of gas turbine combustors ',j. Propul , Vol. 7,No. 3, pp 445-451, 1991.
Karki, K. C., Oechsle, V. L., and Mongio,H.C., 'A computational procedure for diffuser-combustor flow interaction analysis', J. Eng Gas Turbines Power,1992, Vol. 114, pp1-7.
Alkhafagiy, D., and Rahim, A., ' Application0f CFD in combustor design technology', National Conference on State of Art Technologies in Mechanical Engineering, STEM-2007, pp311-316.
Downloads
Published
Issue
Section
License
- Papers must be submitted on the understanding that they have not been published elsewhere (except in the form of an abstract or as part of a published lecture, review, or thesis) and are not currently under consideration by another journal published by any other publisher.
- It is also the authors responsibility to ensure that the articles emanating from a particular source are submitted with the necessary approval.
- The authors warrant that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required.
- The authors ensure that all the references carefully and they are accurate in the text as well as in the list of references (and vice versa).
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Attribution-NonCommercial 4.0 International that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
- The journal/publisher is not responsible for subsequent uses of the work. It is the author's responsibility to bring an infringement action if so desired by the author.
