Investigation of Fuel Flow Velocity on CNG Engine using New Injector

Authors

  • Hari Prastowo
  • Semin Semin Department of Marine Engineering, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
  • M. Badrus Zaman
  • Amiadji, T. Bambang Musrijadi
  • Agoes Santoso
  • Dwi Priyanta
  • Sardono Sarwito
  • Alam Baheramsyah
  • Rosli Abu Bakar

Keywords:

CNG engine, computational simulation, fuel flow velocity, new injector.

Abstract

In this paper, the new injector has been developed based on computational model. The methods of fuel flow velocity investigation from the CNG engine using new injector simulations focused on the combustion chamber area. The fuel flow velocity in the combustion chamber affected the combustion and performance of the engine. From the simulation of every new injector nozzle holes type, the velocity in the combustion chamber was different and most of the velocities were higher and better compared to the original injection nozzle.

References

A.E. Catania, D. Misul, E. Spessa, and A. Vassallo. 2004. Analysis of Combustion Parameters and Their Relation to Operating Variables and Exhaust Emissions in an Upgraded Multivalve Bi-Fuel CNG SI Engine. SAE Paper: 2004-01-0983.

M. Mbarawa. B.E. Milton and R.T. Casey. 2001. Experiments and Modelling of Natural Gas Combustion Ignited by a Pilot Diesel Fuel Spray. Int. J. Therm. Sci. 40: 927–936.

J.B. Heywood. 1988. Internal Combustion Engine Fundamentals. Singapore. McGraw-Hill.

V. Ganesan. 1999. Internal Combustion Engines. New Delhi. Tata McGraw-Hill.

Semin and R.A. Bakar. 2013. Simulation and Experimental Method for the Investigation of Compressed Natural Gas Engine Performance. International Review of Mechanical Engineering 7 (7).

H.M. Cho, and He, Bang-Quan. 2007. Spark Ignition Natural Gas Engines - A review. Energy Conversion and Management 48: 608–618.

Semin. A.R. Ismail. and R.A. Bakar. 2008. Investigation of CNG Engine Intake Port Gas Flow Temperature Based on Steady-State and Transient Simulation. European Journal of Scientific Research 22 (3).

Semin. A.R. Ismail. R.A Bakar and I. Ali. 2008. Heat Transfer Investigation of Intake Port Engine Based on Steady-state and Transient Simulation. American Journal of Applied Sciences 5 (11).

A.R. Ismail. R.A. Bakar. Semin. and I. Ali. 2008. Computer Modelling for 4-Stroke Direct Injection Diesel Engine. Advanced Materials Research Volumes 33-37.

A.R. Ismail. R.A. Bakar and Semin. 2008. An Investigation of Valve Lift Effect on Air Flow and CD of Four Stroke Engines Based on Experiment. American Journal of Applied Sciences 5 (8).

Semin. R.A. Bakar and A.R. Ismail. 2008. Investigation of Diesel Engine Performance Based on Simulation. American Journal of Applied Sciences 5 (6).

Semin. R.A. Bakar and A.R. Ismail. 2008. Computational Visualization and Simulation of Diesel Engines Valve Lift Performance Using CFD. American Journal of Applied Sciences 5 (5).

Semin. A.R. Ismail and R.A. Bakar. 2008. Comparative Performance of Direct Injection Diesel Engines Fueled Using CNG Based on GT-POWER Simulation. American Journal of Applied Sciences 5 (5).

R.A. Bakar. Semin and A.R. Ismail. 2008. Fuel Injection Pressure Effect on Performance of Direct Injection Diesel Engines Based on Experiment. American Journal of Applied Sciences 5 (3).

R.A. Bakar. Semin. A.R. Ismail and I. Ali. 2008. Computational Simulation of Fuel Nozzle Multi Holes Geometries Effect on Direct Injection Diesel Engine Performance Using GT-POWER. American Journal of Applied Sciences 5 (2).

Semin. R.A Bakar. and A.R. Ismail. 2009. Compressed Natural Gas as an Alternative Fuel for Internal Combustion Engines: A Technical Review. International Review of Mechanical Engineering Vol. 3 (2).

Semin. A. Idris. and R.A Bakar. 2009. Effect of Port Injection CNG Engine using Injector Nozzle Multi Holes on Air-Fuel Mixing in Combustion Chamber. European Journal of Scientific Research 34 (1).

Semin. A. Idris. and R.A. Bakar. 2009. An Overview of Compressed Natural Gas as an Alternative Fuel and Malaysian Scenario. European Journal of Scientific Research 34 (1).

Semin. A.R. Ismail. and R.A. Bakar. 2009. Gas Fuel Spray Simulation of Port Injection Compressed Natural Gas Engine using Injector Nozzle Multi Holes. European Journal of Scientific Research 29(2).

Semin, A. Idris. R.A. Bakar. A.R. Ismail. 2009. Study of the Engine Cylinder Fluid Characteristics for Diesel Engine Converted to CNG Engine. European Journal of Scientific Research 26 (3).

Semin. A.R. Ismail. and T.F. Nugroho. 2010. Experimental and Computational of Engine Cylinder Pressure Investigation on the Port Injection Dedicated CNG Engine Development. J. Applied Sci.10 (2). pp: 107-115.

Semin. 2012. Injector Nozzle Spray on Compressed Natural Gas Engines: A Technical Review. International Review of Mechanical Engineering 6. (5).

Semin and R.A. Bakar. 2014. Computational Modelling the Effect of New Injector Nozzle Multi Diameter Holes on Fuel-Air Mixing Homogeneous of CNG Engine. International Journal of Applied Engineering Research. Volume 9 (21). pp. 9983.

Semin. 2015. Analysis of Biogas as an Alternative Fuel for Electric Generator Engine in Bawean Island – Indonesia. International Journal of Applied Engineering Research 10 (16). pp. 35313-35317.

Semin. 2015. Investigation the Effect of Injector Nozzle Multi Holes Geometry on Fuel Spray Distribution Flow of CNG Engine Based on Computational Modeling. International Journal of Applied Engineering Research 10 (15). pp.36087-36095.

Downloads

Published

2016-05-10

How to Cite

Prastowo, H., Semin, S., Zaman, M. B., Musrijadi, A. T. B., Santoso, A., Priyanta, D., Sarwito, S., Baheramsyah, A., & Bakar, R. A. (2016). Investigation of Fuel Flow Velocity on CNG Engine using New Injector. Asian Journal of Engineering and Technology, 4(2). Retrieved from https://ajouronline.com/index.php/AJET/article/view/3772

Issue

Section

Articles